13.56MHz PN532 NFC - Revision history

Chenqi: /* Documents */

2020-04-26T09:17:06Z

‎Documents

Chenqi: /* Arduino */

2020-04-26T08:40:58Z

‎Arduino

Chenqi: /* Arduino */

2020-04-26T08:39:59Z

‎Arduino

Chenqi: /* Documents */

2020-04-26T08:28:35Z

‎Documents

Chenqi: /* Documents */

2020-04-26T08:28:21Z

‎Documents

Chenqi: /* STM32 */

2020-04-26T02:45:50Z

‎STM32

Chenqi: /* Arduino */

2020-04-26T02:34:46Z

‎Arduino

Chenqi: /* UART interface */

2020-04-26T02:29:13Z

‎UART interface

Chenqi: /* Raspberry Pi */

2020-04-26T02:25:13Z

‎Raspberry Pi

Chenqi: /* Raspberry Pi */

2020-04-26T02:24:38Z

‎Raspberry Pi

← Older revision		Revision as of 09:17, 26 April 2020
Line 476:		Line 476:

	[[Media:MF1S50YYX_V1.pdf]]		[[Media:MF1S50YYX_V1.pdf]]
		+
		+	[[Media:PN532_code.zip\|PN532_code.zip]]

@@ Line 327: / Line 327: @@
 =='''Arduino'''==
 {|-
-|[[File:NFC-P532-ADU.jpg|600px|left|NFC-P532-RPI]]
+|[[File:NFC-P532-ADU.jpg|600px|left|NFC-P532-ADU]]
 |}
 . Make sure that you have installed Arduino IDE in your PC

← Older revision		Revision as of 08:39, 26 April 2020
Line 326:		Line 326:

	=='''Arduino'''==		=='''Arduino'''==
		+	{\|-
		+	\|[[File:NFC-P532-ADU.jpg\|600px\|left\|NFC-P532-RPI]]
		+	\|}
	1. Make sure that you have installed Arduino IDE in your PC		1. Make sure that you have installed Arduino IDE in your PC

@@ Line 467: / Line 467: @@
 ='''Documents'''=
 [[Media:pn532_datasheet.pdf]]
 [[Media:pn532_user_manual.pdf]]
 [[Media:NTAG213_215_216.pdf]]
 [[Media:MF1S50YYX_V1.pdf]]

← Older revision		Revision as of 08:28, 26 April 2020
Line 466:		Line 466:

	='''Documents'''=		='''Documents'''=
		+	[[Media:pn532_datasheet.pdf]]
		+	[[Media:pn532_user_manual.pdf]]
		+	[[Media:NTAG213_215_216.pdf]]
		+	[[Media:MF1S50YYX_V1.pdf]]

← Older revision		Revision as of 02:45, 26 April 2020
Line 408:		Line 408:

	=='''STM32'''==		=='''STM32'''==
		+	The development board used here is Open103C which is based on STM32F103CBT6.
		+
		+	===Download project===
		+	1. Open project by keil software（...\MDK-ARM\pn532_stm32.uvprojx），Click Rebuild to compile project.
		+
		+	2. Choose programmer：Options for Target -> Debug-> Use，default: ST-Link Debugger。
		+
		+	3. Choose download method：Options for Target -> Debug -> Settings -> Debug -> Port，Default: JTAG.
		+
		+	4. Connect Open board to PC by programmer. Note that you should power Open board separately.
		+
		+	5. Click Download to download project.
		+
		+	===Hardware connection===
		+	===SPI connecting===
		+
		+	1. Set L0 to L and L1 to H by jumpers
		+
		+	2. Set DIP switch to
		+
		+	SCK MISO MOSI NSS SCL SDA RX TX
		+	ON ON ON ON OFF OFF OFF OFF
		+	3. Connect PN632 to Open103C board
		+
		+	Connect PN532 NFC HAT to STM32F via SPI interface
		+	PN532 NFC HAT STM32F103CBT6
		+	SCK PA5
		+	MISO PA6
		+	MOSI PA7
		+	NSS PA4
		+	PN532 NFC HAT-5.png
		+	===I2C connecting===
		+
		+	1. Set L0 to L and L1 to H by jumpers
		+
		+	2. Set DIP switch to
		+
		+	SCK MISO MOSI NSS SCL SDA RX TX
		+	OFF OFF OFF OFF ON ON OFF OFF
		+	3. Connect PN632 to Open103C board
		+
		+	Connect PN532 NFC HAT to STM32F via I2C interface
		+	PN532 NFC HAT STM32F103CBT6
		+	SCL PB6
		+	SDA PB7
		+	===Software setting===
		+	Open project and choose the interface according to interface used. recompile and download
		+	<pre>
		+	// PN532_SPI_Init(&pn532);
		+	PN532_I2C_Init(&pn532);
		+	</pre>
		+	4. Connect USB to TTL module to UART1 interface (PA9->RX, PA10->TX） of STM32 and PC.
		+
		+	5. Open serial assistant software, and reset Open103C
		+
		+	6. Expected result: close card to coil part of PN532, the UID of card is read and printed.
		+
	='''Documents'''=		='''Documents'''=

← Older revision		Revision as of 02:29, 26 April 2020
Line 191:		Line 191:
	\|}		\|}

−	~~PN532 NFC HAT-3.jpg~~
	4. Connect PN532 to Raspberry Pi		4. Connect PN532 to Raspberry Pi

@@ Line 104: / Line 104: @@
 =='''Raspberry Pi'''==
 Download demo code from #Resources, unzip and copy raspberrypi folder to /home/pi of Raspberry Pi. You can firstly copy it to /boot of SD card, then copy it to /home/pi.
 {|-
-|[[File:NFC-P532-RPI.jpg|900px|left|NFC-P532-RPI]]
+|[[File:NFC-P532-RPI.jpg|600px|left|NFC-P532-RPI]]
 |}
 ===SPI Interface===